solid outlet
英 [ˈsɒlɪd ˈaʊtlet]
美 [ˈsɑːlɪd ˈaʊtlet]
【化】滤渣出口，滤渣排出口
双语例句
- A device used for solid material drinking is characterized in that a solid material container, a liquid inlet suction pipe and a liquid outlet suction pipe are included;
一种用于饮用固体物料的器具，其特征在于它包括固体物料容器、进液吸管和出液吸管； - At the different concentration rate the change of quasi-steady filtrate flux, viscosity and wet solid content for inosine fermentation broth were investigated by industrialized ceramic membranes. On basis of this, membrane filtrate flux can be enhanced in the process of inlet in exchange with outlet.
以工业化陶瓷膜考察了肌苷发酵液在不同浓缩比下的拟稳定通量、粘度及湿固含量变化，在此基础上，将发酵液进、出口调换，可使膜通量提高； - This technique was distinct not only for the composition of the absorbefacient, but also for the fact that it accomplished the relative moving of the liquid and solid by continually changing the location of the inlet and outlet of the flow.
这种专利技术不仅体现在吸附剂原料的组成，更重要的是体现在它通过各股物料出入口位置不断切换来实现液相与固相之间的相对移动。 - In this paper, the effect of total solid content in slurry, inlet temperature and outlet temperature of spraying drier on the yield of cheese powder were analyzed by orthogonal rotational regression design. The regression equation was established and the spraying drier conditions were optimized.
针对影响干酪粉出品率的喷雾干燥条件，采用三因素二次通用旋转回归设计对其进行了优化，并建立了回归方程。 - It is found that with an increase in the gas nozzle outlet speed the maximum static pressure in the gas solid injector will shift from near the inlet of the injector convergent section to a location near the outlet of the injector convergent section.
提高气体喷嘴出口速度，气固喷射器内的最大静压值由喷射器收缩段入口处附近迁移至喷射器收缩段出口处附近。 - The Effect of a Central Flared Angle on the Gas solid Flow Characteristics at the Outlet of a Radial Bias and Pulverized coal Swirl Burner
中心扩口对径向浓淡旋流煤粉燃烧器出口气固流动特性的影响 - The design tool includes three levels, i.e. system, device and process level, which took the netlist, solid model and layout as the design data flow inlet and outlet for each level separately.
该方法采用通用的系统级、器件级和工艺级的三级架构，但以网表、标准格式的实体模型和版图文件分别作为这三个级别设计数据的出入口。 - Based on the test results the optimal conditions were as follows: Malt dextrin: micro-porus starch was 1 ∶ 1, pigment content was 10%, solid content was 40%. spray drying inlet air temperature 140 ℃, outlet air 80 ℃.
试验结果表明最佳条件为：麦芽糊精∶微孔淀粉1∶1，色素含量10%，总固形物含量40%，喷雾干燥进风温度140℃，出风温度80℃。 - In processing the tiny hole on printed circuit board precision is effected by the tiny diameter of the solid drill, its poor rigdity and excessive difference between locations of the inlet and the outlet of the drill.
在印刷电路板的微孔加工中，因钻头的直径很小，刚性较差，钻孔的出口与入口位置偏差过大，而影响微孔加工的精度。 - The results indicated that the material conveying capacity and tank pressure increased, the material mass ratio of solid and gas in the outlet decreased with the raising of fluidized air quantity.
试验结果表明，物料输送量和流化罐压力随着流化空气量的增加而增加；流化罐出口物料固气质量比随着流化空气量的增加而减小。 - In addition, the influence of spray drying technologies such as solid content, inlet temperature and outlet temperature on the product quality was further studied and optimum process was concluded.
同时考察了喷雾干燥工艺（如固形物浓度、进风温度和出风温度）对产品质量的影响，得到了优化的喷雾干燥工艺。